Kenmore Elite 95073 Installation Guide download pdf

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Clearances and Dimensions

1. Provide adequate clearances between the range and adjacent combustible surfaces.

2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor.

3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid

and level.

*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED WOOD OR METAL

CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT

MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020"

COPPER. 0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE

TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.

TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED

ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY

INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.

p/n 316454920 rev A

Important Notes to the Installer

• Read all instructions contained in these installation instructions

before installing range.

• Remove all packing material from the oven compartments

before connecting the gas & electrical supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

Fig. 1

Fig. 2

Fig. 3

30"

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE

Español - Páginas 5-8

Important Note to the Consumer

Keep these instructions with your owner's guide for future

reference.

• As when using any appliance generating heat, there are

certain safety precautions you should follow. These are listed

in the

Use & Care Guide, read it carefully.

• Be sure your range is installed and grounded properly by a

qualified installer or service technician.

• Make sure the wall coverings around the range can withstand

the heat generated by the range.

• To eliminate the need to reach over the surface elements,

cabinet storage space above the elements should be

avoided.

If the information in this manual is not followed

exactly, a fire or electrical shock may result causing property

damage, personal injury or death.

Tip Over Hazard

• A child or adult can tip the range and be

killed.

• Verify the anti-tip device has been installed

to floor or wall.

• Ensure the anti-tip device is re-engaged

when the range is moved to floor or wall.

To check if the anti-tip bracket is installed properly, use both arms

and grasp the rear edge of range back. Carefully attempt to tilt

range forward. When properly installed, the range should not tilt

forward. Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

• Do not operate the range without the anti-tip device in place

and engaged.

• Failure to follow these instructions can result in death or

serious burns to children and adults.

Range

leveling leg

Anti-Tip

bracket

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.READ AND SAVE THESE INST

Page 2

1. ANTI-TIP BRACKET INSTALLATION INSTRUCTIONS- IMPORTANT SAFETY WARNINGTo reduce the risk of tipping of the range, the range must besecured to the flo

Page 3 - 4A. POWER CORD CONNECTIONS

2b. MODELS REQUIRING POWER SUPPLY CORD KIT.RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF ANINCORRECT SIZE RANGE CORD KIT IS USED, THEINSTALLATION INST

Page 4

or 4B. POWER CORD CONNECTIONS(3-Wire Connection Instructions . For existing installations ONLY -Refer to Fig. 13).1. Follow the manufacturer’s install

Page 5 - 30"

5LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO.IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL

Page 6 - Deslice la

6Fig. 7Costadode laestufa11/16"Deslice laestufahacia atrásANTES DE COMENZARHerramientas NecesariasPara los tornillos niveladores y soporte antivu

Page 7 - DE ALIMENTACION ELECTRICA

7NOTA: La estufa es embarcada de la fábrica con un agujero de 1-3/8" de diámetro como se muestra. Para usar ya sea el agujero de7/8" de diá

Page 8 - (NEUTRO)

84c. CONEXIONES DEL CABLEADO PERMANENTE TRIFILAR YTETRAFILAR.3 - Conexión trifilar permanente - siga los pasos 1, 2 y 5 incluidos a continuación.4 - C